Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Launch the ReXdesk software and click the ‘Help’ tab on the navigation bar.
Click the License option in the drop-down menu.
Click ‘Import’ to enter the license key.
Enter the ‘License identification code’ (provided by Influx) and click ‘OK’.
Once complete, the License status will be set to ‘Active’.
Bus and signals
Operating voltage
Safe applied voltage
Power supply - OBD
+5V to +27V
±34V
Power supply - USB
+4.5V to +5.5V
0V to +6V
CAN/CAN FD
+2V to +3V
± 28V
ANALOG Input
± 10 V
± 28V
DIGITAL INPUT
LOW < +0.8 V
HIGH > 2.5 V
± 28V
Pin No
Pin Function
Pin 1
Digital 1
Pin 2
CAN 0 – Low
Pin 3
GND
Pin 4
LIN
Pin 5
Power GND
Pin 6
Digital 0
Pin 7
CAN 0 – High
Pin 9
Power Supply +5V to +27V
Pin No
Pin Function
Pin 1
AnalogGND
Pin 2
CAN 1 – Low
Pin 3
GND
Pin 4
Analog IN 0
Pin 5
AnalogGND
Pin 6
Analog IN 1
Pin 7
CAN 1 – High
Pin 8
Clamp-15
There is one 9-pin Standard D-Type connector.
The connector needs to be tightened properly to make a proper connection, ensuring reliable operation.
Each end of the CAN bus must be terminated with a 120 Ohm resistor across CAN H & CAN L.
Do not short-circuit any pins.
The maximum safe applied voltage for analogue and digital I/P is +/- 28 V.
Before proceeding with the installation, please ensure you have acquired administrative privileges.
To install the ReXgen driver, run the .exe file in this location:
C:\Program Files (x86)\Influx Technology\ReXdesk\Drivers.
The .exe file can also be found in the start menu under ‘influxtechnology.
Run the ReXgenInstaller.exe file.
Click ‘Next’ to continue installing the ReXgen device driver on your system.
To cancel the installation at this stage, click ‘Cancel’. (No software will have been installed on the system now.)
Please read the license agreement carefully.
Once you understand and accept the license agreement, please click ‘I accept this EULA’ to continue with the installation of the driver. If you do not accept the terms, please click ‘Cancel’ to stop the installation at this point.
Click ‘Next’ to continue the installation process.
Once the installation is complete, this window will appear.
Click ‘Finish’ to close the window. The ReXgen driver is now successfully installed on your system.
Pin No
Pin Function
Pin 1
NC
Pin 2
CAN-Low
Pin 3
GND
Pin 4
Nc
Pin 5
Power GND
Pin 6
NC
Pin 7
CAN-High
Pin 9
Power Supply+5 to +27V
Before proceeding with the installation, please ensure that you have acquired administrative privileges.
Make sure you have installed the Microsoft Visual C++ Redistributable (x86) and,
Dotnet runtime 4.7.2 is required
You can download it from the following link:
To begin the installation of the ReXdesk software, open the installer by running the set-up file.
Click ‘Next’ to start the installation.
To continue installing ReXdesk on your system, click ‘Next’.
To cancel the installation at this stage, click ‘Cancel’ (No software will have been installed on the system yet).
Select the folder in which you wish to install the software. It’s preferred to use the default location.
Select the preference for computer user installation to determine which computer users will access the ReXdesk software.
Click ‘Next’ to continue with the installation.
To continue installing ReXdesk on your system, click ‘Next’.
Once the installation is complete, this window will appear.
Click ‘Close’ to close the window. ReXdesk is now successfully installed on your system.
There are two connectors, a 24-pin Molex Mini50 connector and a male 25-pin Standard D Type connector
The connector needs to be tightened properly to make a proper connection, ensuring reliable operation.
Each end of the CAN bus must be terminated with a 120 Ohm resistor across CAN H & CAN L.
Do not short-circuit any pins.
The maximum safe applied voltage for analogue and digital I/P is ±28 V.
Pin No
Pin Function
Pin 3
CAN Bus 3 Low Signal (Available only on 4x CAN Model)
Pin 4
Analog Input 1 - do not apply voltages outside of the -10 to +10V range
Pin 5
Wake-Up pin to wake logger from sleep mode
Pin 6
CAN Bus 1 Low Signal
Pin 7
CAN Bus 0 Low Signal
Pin 9
+5 to +27V Supply Voltage
Pin 10
+4.5V Instrumentation Supply Voltage, ensure that current draw is not more than 100mA
Pin 11
Erase PIN
Pin 12
Digital Input 0 - When used as an input, do not apply voltages outside the 0 to +12V range. More information on the use of this pin can be found in Appendix 2
Pin 13
CAN Bus 2 Low Signal (Available only on 4x CAN Model)
Pin 15
LIN 0 Signal
Pin 16
CAN Bus 3 High Signal (Available only on 4x CAN Model)
Pin 17
Analog Input 0 - do not apply voltages outside of the -10 to +10V range
Pin 18
Analog Ground
Pin 19
CAN Bus 1 High Signal
Pin 20
CAN Bus 0 High Signal
Pin 21
Ground
Pin 22
Power Ground
Pin 23
Relay Out (Optional Feature)
Pin 24
Digital Input 1 - When used as input, do not apply voltages outside the 0 to +12V range
More information on the use of this pin can be found in Appendix 2
PIN 25
CAN Bus 2 High Signal (Available only on 4x CAN Model)
PIN No
PIN Function
Optional
Pin 1
RelayOut0
Relay Driver
Pin 2
DigIn0
Pin 3
AnalogGnd
Pin 4
Adc1
Pin 5
Wake-UP/Clamp-15
Pin 6
CAN0-L
Pin 7
CAN1-L
Pin 8
CAN2-L
Additional CAN FD 3rd bus
Pin 9
CAN3-L
Additional CAN FD 4th bus
Pin 10
usbDP_conn
Request when ordering
Pin 11
4.5Vout
Pin 12
DIgIn1
Pin 13
Adc0
Pin 14
Erase#
Pin 15
LIN
Pin 16
GND
Pin 17
PowerGND
Pin 18
+5 to +27V
Pin 19
CAN0-H
Pin 20
CAN1-H
Pin 21
CAN2-H
Additional CAN FD 3rd bus
Pin 22
CAN3-H
Additional CAN FD 4th bus
Pin 23
usb5V
Request when ordering
Pin 24
usbDM_conn
Request when ordering
