Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
The CAN connectors are 1x Male and 1x Female 9-pin Subminiature D Type connectors.
DB9
Pin Function
Pin 2
CAN L
Pin 3
CAN Ground
Pin 5
Power Ground
Pin 7
CAN H
Pin 9
Power Supply 4.5-31V
The Thermocouple connectors on the K-TC are miniature-size flat-type sockets.
IEC Connector
Pin Function
Top
+
Bottom
K
The dimensions of the Male Flat Type Miniature Size Thermocouple Plug that you would plug into it are as follows:
The K-TC 2.0 is Influx's upgraded version of the older K-TC modules. Like the previous modules, these are stackable instrumentation devices compatible with Influx's entire range of data loggers. These can also be integrated with any device configured via DBC files, other logger systems, or output signals on CAN for the Rebel Dash display.
The K-TC 2.0 is an ideal solution for applications that require a large number of thermocouple inputs. The K-TC 2.0's accurate sensor data is transmitted periodically on the CAN bus, enabling multiple devices to be connected. In addition, the temperature data is simultaneously logged in the inbuilt micro-SD card (8GB), the K-TC 2.0 CAN bus settings, calibration, and sampling rates are all easily configurable, and these settings are stored within the K-TC 2.0 even when the device is not powered.
Power supply
4.5 to 31V DC (isolated)
Power consumption
K-TC8 / K-TC16 / K-TC32
Normal operation
120mA at 12V / 140mA at 12V / 200mA at 12V
Power down standby mode
24mA at 12V / 25mA at 12V / 30mA at 12V
Configuration
Via CAN bus with K-Cal for calibration. Via USB with TC Logger SW for logging configurations stored in the device
Interfaces (Isolated)
CAN bus (max 1000 kbps) and USB 2.0
Storage
8 GB eMMc
PC Interfaces
USB2.0 Type B (isolated)
Enclosure
Dimension (LxHxW): 115x56(K-TC8) / 79(K-TC16) / 149(K-TC32) x 105mm
Weight 450g(K-TC8), 570g(K-TC16), 900g(K-TC32)
IP 65 (With all thermocouples plugged in)
ABS/Aluminium Allow* (depending upon the stock availability)
Environmental
-40°C to +85°C
Humidity max 90%
Thermocouple Inputs
K, J, T-type
Accuracy ± 1°C
Measurement: -200 °C to 1250 °C
Connection type
Thermocouples: mini K, J ,T-Type (galvanically isolated)
Thermocouple Inputs
Number of channels
K-TC8: 8 channels, K-TC16: 16 channels, K-TC32: 32 channels (group of 8 thermocouples - each galvanically isolated)
Channel Input Types
K, J, T
Measurement Range
(-)200°C to (+)1200°C
Max Sampling Rate
20 Hz per channel
Max applied voltage
± 3.3 V
Peak Galvanic Isolation Voltage
(from all other modules and power supplies)
Three-wire CAN Bus
780 V
Four-wire USB Bus
840 V
Two-wire power module
560V
The Rebel drivers must be correctly installed to ensure the Rebel functions correctly.
If DiaLog is installed, a driver installation application will be available, which can be found in the Influx Technology folder of the Start Menu, as shown below.
Ensure the Rebel is not plugged in and click ‘Next’ to continue.
Please read and accept the EULA, then click next to continue.
The driver installation will begin and may take a few moments.
Once the installation is complete, click ‘Finish’ to close the application.
Plugin the Rebel to allow the drivers to be recognised.
Before proceeding with the installation, please ensure you have acquired administrative privileges.
To install the K-TCxx driver, run the .exe file in this location:
The .exe file can also be found in the start menu under ‘influx technology.
Run the K-TCxx Installer.exe file.
Click 'Next' to continue installing the K-TCxx device driver on your system.
To cancel the installation at this stage, click ‘Cancel’. (No software has been installed on the system at this point.)
Please read the license agreement carefully.
Once you understand and accept the license agreement, please click ‘I accept this EULA’ to continue with the driver’s installation. If you do not accept the terms, please click ‘Cancel’ to stop the installation at this point.
Click ‘Next’ to continue the installation process.
Once the installation is complete, this window will appear.
Click ‘Finish’ to close the window. The K-TCxx driver is now successfully installed on your system.
Download the ReXgen J2534 Driver by clicking the below link and execute the file. - https://downloads.influxtechnology.com/ReXdesk/Rexgen_J2534_Installer.zip
Double click on ReXgen j2534 Installer
Click 'Cancel' to abort installation.
Click 'Install'.
Click 'Close'.
Run the K-TCxxCal.msi
Click Next to start the installation
The program installation window appears.
Click “Cancel” if you do not wish to install it.
After the K-TCxxCal software is installed, click finish