1 of 94

Pinouts: Influx Product Range

Cables & Device Pinouts: Influx Product Range

INF 41XX.XX

INF4100: Rebel Start-Up Kit Harness

This cable is specifically designed to work with the Rebel 100, making it easier access the data loggerIO during the early engineering development stages.

The Rebel 100 is designed to be installed for long term event monitoring on production machinery and therefore the connector type is the same that you would normally find on an ECU. This type of connector is not very convenient for engineering development since these connectors are harder to work with. The Rebel100 start-up harness will enable you to connect to the Rebel 100 using standard9 PIN D-Sub connectors like the Rebel CT multi-connect cable.

Tech Specs:

Data Logger Socket.

Pin

Pin Function

Pin

Pin Function

Pin

Pin Function

CAN 1-L

CAN 1-H

Dig0

CAN 0-L

CAN 0-H

Dig1

CAN 3-L

CAN 3-H

Dig2

CAN 2-L

CAN 2-H

Dig3

K-Line

Wake-up#

6-41V

Erase#

GND

PowerGND

Ain3_inst

GNDa

usb_+5V

Ain2_inst

GNDa

usb_GND

Ain1_inst

GNDa

usb_D+

Ain0_inst

GNDa

usb_D-

CAN0/CAN1/Kline/PWR Connector

Male 9-pin standard D-type connector with screws

Note:

Pins not mentioned in the description table(s) are NC.

CAN 1 Connector

Female 9-pin standard D-Type connector with screws

Pin No

Pin Function

Pin 2

CAN Bus 1 (Medium Speed Bus) Low Signal

Pin 3

Ground

Pin 5

Ground

Pin 7

CAN Bus 1 (Medium Speed Bus) High Signal

Note:

Pins not mentioned in the description table(s) are NC.

CAN 2 Connector

Male 9-pin standard D-type connector with nuts

Pin No

Pin Function

Pin 2

CAN 2 Bus Low Signal

Pin 3

Power Ground

Pin 7

CAN 2 Bus High Signal

Note:

Pins not mentioned in the description table(s) are NC.

CAN 3 Connector

Male 9-pin standard D-type connector with nuts

Pin No

Pin Function

Pin 2

CAN 3 Bus Low Signal

Pin 3

Power Ground

Pin 7

CAN 3 Bus High Signal

Note:

Pins not mentioned in the description table(s) are NC.

Digital and Analog Connector

Male 15-pin standard D-type connector with screws

Pin No

Pin Function

Pin 2

Digital Input or Output 1 - When used as an input do not apply voltages outside of the 0 to +12V range, when used as an Output ensure that current draw is not more than 50mA.

More information on use of this pin can be found in Appendix 2 and 3

Pin 4

Ground

Pin 5

Erase

Pin 6

Analog Ground

Pin 7

Analog Input 1 - do not apply voltages outside of the -10 to +10V range

Pin 8

Analog Input 3 - do not apply voltages outside of the -10 to +10V range

Pin 9

Digital Input or Output 0 - When used as an input do not apply voltages outside of the 0 to +12V range, when used as an Output ensure that current draw is not more than 50mA.

More information on use of this pin can be found in Appendix 2 and 3-Normal

Pin 10

Digital Input or Output 2 - When used as an input do not apply voltages outside of the 0 to +12V range, when used as an Output ensure that current draw is not more than 50mA.

More information on use of this pin can be found in Appendix 2 and 3

Pin 11

Ground

Pin 13

Wake-Up pin to wake logger from sleep mode (for use see Appendix 1)

Pin 14

Analog Input 0 - do not apply voltages outside of the -10 to +10V range

Pin 15

Analog Input 2 - do not apply voltages outside of the -10 to +10V range

Note:

Pins not mentioned in the description table(s) are NC.

INF4102: 180-degree OBD Type-B Cable to Rebel Data Logger Adapter Cable

Note that Type B can connect to type A port.

Tech Specs:

Parameter

Value

Cable Length

1700mm

Cable Thickness

22 AWG TBC

Connector A

25-pin D-sub (DB25) socket

Connector B

OBDII 16-pin connector

Temperature

Operating temperature: -20degC to +80degC

Weight

247 g

Colour

Black

25-Way D-Type

Female 25-pin standard D-Type connector

Note:

Pins not mentioned in the description table(s) are NC.

OBDII Connector

Male 16-pin OBDII connector

Pin No

Pin Function

Pin 3

CAN Bus 1 (Medium Speed Bus) High Signal

Pin 4

Power Ground

Pin 5

Ground

Pin 6

CAN Bus 0 (High Speed Bus) High Signal

Pin 7

K-Line (1 wire bus) of ISO 9141

Pin 11

CAN Bus 1 (Medium Speed Bus) Low Signal

Pin 14

CAN Bus 0 (High Speed Bus) Low Signal

Pin 16

4.5-36V Supply Voltage

Note:

Pins not mentioned in the description table(s) are NC.

INF4103: 180-degree OBD Type-B to 9-Way Sub D Adapter Cable

How to use with the Rebel data loggers

To use this cable with a Rebel data logger you will also need one of our Rebel multi-connect breakout cables. This cable combination enables CAN 0 of the Rebel data logger to be directly connected to the vehicle diagnostic CAN bus and also the permanent battery supply.

Use with either:

INF4203: 2 CAN breakout cable (4 Lead)
INF4204.1: Multi-Connect Cable for Rebel data loggers (5 Lead)

How to use with the ReXgen data loggers

This cable enables a direct connection from the ReXgen 9 Way D-Sub to the vehicle diagnostic

CAN bus and also the permanent battery supply.

How to use with Kvaser Interfaces

This cable enables a direct connection from the Kvaser 9-Way D-Sub to the vehicle diagnostic CAN bus and battery supply.

Note that Type B can connect to type A port.

Tech Specs:

Parameter

Value

Cable Length

1700mm

Cable Thickness

22 AWG TBC

DB9 Pins

In accordance with CiA 303 - 1

Connector A

9-pin D-sub (DB25) socket

Connector B

OBDII 16-pin connector

Operating temperature

-20degC to +80degC

Weight

236 g

Colour

Black

9-Way D-Type

Female 9-pin standard D-Type connector

Pin No

Pin Function

Pin 2

CAN Bus 0 (High Speed Bus) Low Signal

Pin 3

Ground

Pin 4

K-Line (1 wire bus) of ISO 9141

Pin 5

Power Ground

Pin 7

CAN Bus 0 (High Speed Bus) High Signal

Pin 9

4.5-36V Supply Voltage

Note:

Pins not mentioned in the description table(s) are NC.

OBDII Connector

Male 16-pin OBDII connector

Pin No

Pin Function

Pin 4

Power Ground

Pin 5

Ground

Pin 6

CAN Bus 0 (High Speed Bus) High Signal

Pin 7

K-Line (1 wire bus) of ISO 9141

Pin 14

CAN Bus 0 (High Speed Bus) Low Signal

Pin 16

4.5-36V Supply Voltage

Note:

Pins not mentioned in the description table(s) are NC.

INF 42XX.XX

INF4202: Rebel FlexRay/CAN Breakout Cable

Connects to the expansion port of the Rebel CT FlexRay and Rebel CT 7 data logger. The LIN bus, CAN buses and FleXray channels are connected to separate 9-Way D-Sub moulded connectors. This cable consists of two FlexRay connectors, three CAN buses connectors and one LIN connector.

Tech Specs:

Parameter

Value

Cable Length

700 mm

Cable Thickness

22 AWG 0.6 mm

Connector A

Micro D (DB15) socket, compatible with the Rebel CT FlexRay and RebelCT 7 dataloggers communication expansion port.

Connector B

9-pin D-sub (DB9) socket, pins compatible with CiA 303-1 (CAN 4 & LIN3)

Connector C

9-pin D-sub (DB9) socket, pins compatible with CiA 303-1 (CAN 5)

Connector D

9-pin D-sub (DB9) socket, pins compatible with CiA 303-1 (CAN 6)

Connector E

9-pin D-sub (DB9) plug, FleXray channel A

Connector F

9-pin D-sub (DB9) plug, FleXray channel B

Temperature

Operating temperature: -20degC to +80degC

Weight

236 g

Colour

Black

FlexRay 1 Connector

Male 9-pin standard D-type connector

Pin No

Pin Function

Pin 2

FlexRay Bus 1 BM Signal

Pin 3

Ground for the FlexRay Buses

Pin 5

Power Ground

Pin 7

FlexRay Bus 1 BP Signal

Note:

Pins not mentioned in the description table(s) are NC.

FlexRay 2 Connector

Male 9-pin standard D-type connector

Pin No

Pin Function

Pin 2

FlexRay Bus 2 BM Signal

Pin 3

Ground for the FlexRay Buses

Pin 5

Power Ground

Pin 7

FlexRay Bus 2 BP Signal

Note:

Pins not mentioned in the description table(s) are NC.

CAN 4 and LIN 3 Connector

Female 9-pin standard D-type connector

Pin No

Pin Function

Pin 2

CAN Bus 4 (Ext 1) Low Signal

Pin 3

Ground for the CAN and LIN Buses

Pin 4

LIN 3 (Local Interconnect Network) Bus

Pin 5

Power Ground

Pin 7

CAN Bus 4 (Ext 1) High Signal

Note:

Pins not mentioned in the description table(s) are NC.

CAN 5 Connector

Female 9-pin standard D-type connector

Pin No

Pin Function

Pin 2

CAN Bus 5 (Ext 2) Low Signal

Pin 3

Ground for the CAN and LIN Buses

Pin 5

Power Ground

Pin 7

CAN Bus 5 (Ext 2) High Signal

Note:

Pins not mentioned in the description table(s) are NC.

CAN 6 Connector

Female 9-pin standard D-type connector

Note:

Pins not mentioned in the description table(s) are NC.

INF4203: Rebel LT CAN Bus Breakout Cable

This 230 mm breakout cable is supplied with each Rebel LT data logger making it suitable to connect devices that are compliant with the standard CIA 9-PIN D-Sub pinout directly to the data loggers.

The cable has one 25-Way D-Sub connector, which connects directly to the Rebel LT data logger and two 9-Way D-Sub connectors as described here:

This cable is suitable for LT Data Loggers and can also be used to supply power directly to the K-series modules or the Rebel Dash from the Rebel data loggers. This helps to make the installation of our data loggers and instrumentation modules easy and with less cables required.

Tech Specs:

Parameter

Value

Cable Length

230mm

Cable Thickness

24 AWG 0.5 mm

Connector A

25-pin D-sub (DB25) socket, compatible with Rebel CT and Rebel LT data loggers

Connector B

9-pin D-sub (DB9) plug/nuts, pins compatible with CiA 303-1 (CAN 0 and Power)

Connector C

9-pin D-sub (DB9) socket, pins compatible with CiA 303-1 (CAN 1 and LIN)

Temperature

Operating temperature: -20degC to +80degC

Weight

142 g

Colour

Black

OBD and INST Connector

Note:

Pins not mentioned in the description table(s) are NC.

INF4204.15: MOLEX – 5WAY DB9 SPLITTER CONNECTOR

This 15 mm breakout cable is supplied with each ReXgen Air data logger, making it suitable for connecting devices compliant with the standard CIA 9-pin D-Sub pinout directly to our data loggers.

The cable has one 24-Way Molex connector, which connects directly to the ReXgen Air data logger and four 9-Way D-Sub connectors to connect up to the separate CAN buses and one 15-Way D-Sub as described here:

Tech Spec:

Cable Length

15 Cm

Cable OD

6.5mm Twisted pair CAN connections

Connector

DB9 M with screw*1PCS

DB9 M with screw *1PCS

DB9 M with studs*1PCS

DB15FwithScrew*1PCS

Molex mini-50 Female

Molex Connector:

Pins

Molex mini-50

Pins

Molex mini-50

Pin 1

RelayOut0

Pin 13

ADC0

Pin 2

DigIn0

Pin 14

ERASE

Pin 3

AnalogGND

Pin 15

LIN

Pin 4

ADC1

Pin 16

GND

Pin 5

Wakeup/Clamp- 15

Pin 17

Power GND

Pin 6

CAN0 Lo

Pin 18

5-31V

Pin 7

CAN1 Lo

Pin 19

CAN0 Hi

Pin 8

CAN2 Lo

Pin 20

CAN1 Hi

Pin 9

CAN3 Lo

Pin 21

CAN2 Hi

Pin 10

USB DP_Conn

Pin 22

CAN3 Hi

Pin 11

4.5V Out

Pin 23

USB 5V

Pin 12

DigIn1

Pin 24

USB DM_Conn

Digital/Analog Pin (DB-15 Male)

PIN

DIG/ANALOG

PIN

DIG/ANALOG

Pin 1

Pin 9

DigIn 0

Pin 2

4.5V Out

Pin 10

DigIn 1

Pin 3

USB Dp_Conn

Pin 11

GND

Pin 4

USB 5V

Pin 12

Pin 5

USB DM_Conn

Pin 13

WAKE UP/Clamp 15

Pin6

Analog GND

Pin 14

ADC 0

Pin 7

ADC 1

Pin 15

Pin 8

CAN0/Power (DB-9 Male)

PIN

CAN0/PWR

Pin 1

Pin 2

CAN0 Lo

Pin 3

GND

Pin 4

Pin 5

Power GND

Pin6

Pin 7

CAN0 Hi

Pin 8

Pin 9

5-31V

CAN1 (DB-9 Male)

PIN

CAN1

Pin 1

Pin 2

CAN1 Lo

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

CAN1 Hi

Pin 8

Pin 9

CAN 2 (DB-9 Male)

PIN

CAN2

Pin 1

LIN

Pin 2

CAN2 Lo

Pin 3

GND

Pin 4

Pin 5

Power GND

Pin6

Pin 7

CAN2 Hi

Pin 8

Pin 9

CAN 3 (DB-9 Male)

PIN

CAN3

Pin 1

Pin 2

CAN3 Lo

Pin 3

Pin 4

Pin 5

Pin6

Pin 7

CAN3 Hi

Pin 8

Pin 9

Rebel Data Logger Connector

Female 25-pin standard D-Type connector with screws

Pin No

Pin Function

Pin 1

Analog Input 3 - do not apply voltages outside of the -10 to +10V range

Pin 2

LIN 1

Pin 3

CAN/CAN FD 3 L

Pin 4

Analog Input 1 - do not apply voltages outside of the -10 to +10V range

Pin 5

Wake-Up pin to wake logger from sleep mode (for use see Appendix 1)

Pin 6

CAN Bus 1 (Medium Speed Bus) Low Signal

Pin 7

CAN Bus 0 (High Speed Bus) Low Signal

Pin 8

K-Line (1 wire bus) of ISO 9141

Pin 9

4.5-36V Supply Voltage

Pin 10

+4.5V Instrumentation Supply Voltage, ensure that current draw is not more than 100mA

Pin 11

Digital Input or Output 2 - When used as an input do not apply voltages outside of the 0 to +12V range, when used as an Output ensure that current draw is not more than 100mA.

More information on use ofthis pin can be found in Appendix 2 and 3

Pin 12

Digital Input or Output 0 - When used as an input do not apply voltages outside of the 0 to +12V range, when used as an Output ensure that current draw is not more than 100mA.

More information on use ofthis pin can be found in Appendix 2 and 3

Pin 13

CAN/CAN FD Bus 2 (Instrumentation Bus) Low Signal

Pin 14

Analog Input 2 - do not apply voltages outside of the -10 to +10V range

Pin 15

LIN 0

Pin 16

CAN/CAN FD 3 H

Pin 17

Analog Input 0 - do not apply voltages outside of the -10 to +10V range

Pin 18

Analog Ground

Pin 19

CAN Bus 1 (Medium Speed Bus) High Signal

Pin 20

CAN Bus 0 (High Speed Bus) High Signal

Pin 21

Ground

Pin 22

Power Ground

Pin 23

Digital Input or Output 3 (can also be used as a switched power supply +Vd)

Pin 24

Digital Input or Output 1 - When used as an input do not apply voltages outside of the 0 to +12V range, when used as an Output ensure that current draw is not more than 100mA.

More information on use ofthis pin can be found in Appendix 2 and 3

Pin 25

CAN/CAN FD Bus 2 (Instrumentation Bus) High Signal

WARNING

DO NOT SHORT CIRCUIT OR OVERLOAD ANY DIGITAL I/O e.g. IF USING DIGITAL INPUT OR OUTPUT 3 TO SUPPLY POWER TO A K-BOX OR A REBEL DASH, DO NOT CONNECT MORE THAN 1 K-BOX TO THIS OUTPUT AND BE CAREFUL THAT NO SHORT-CIRCUIT OCCURS.

WARNING

DO NOT SHORT CIRCUIT OR OVERLOAD PIN10 (+4.5V INSTRUMENTATION)

ReXgen Air

There are two connectors, a 24-pin Molex Mini50 connector and a male 25-pin Standard D Type connector

1MB

ReXgen Air_V1.2.pdf

pdf

24-pin Molex Mini50 Connector

PIN No

PIN Function

Optional

Pin 1

RelayOut0

Relay Driver

Pin 2

DigIn0

Pin 3

AnalogGnd

Pin 4

Adc1

Pin 5

Clamp-15

Pin 6

CAN0-L

Pin 7

CAN1-L

Pin 8

CAN2-L

Additional CAN FD 3rd bus

Pin 9

CAN3-L

Additional CAN FD 4th bus

Pin 10

usbDP_conn

Request when ordering

Pin 11

4.5Vout

Pin 12

DIgIn1

Pin 13

Adc0

Pin 14

Erase#

Pin 15

LIN

Pin 16

GND

Pin 17

PowerGND

Pin 18

5V to 27V

Pin 19

CAN0-H

Pin 20

CAN1-H

Pin 21

CAN2-H

Additional CAN FD 3rd bus

Pin 22

CAN3-H

Additional CAN FD 4th bus

Pin 23

usb5V

Request when ordering

Pin 24

usbDM_conn

Request when ordering

Male 25-pin Standard D Type connector (Mini 50 to D Sub 25 cable Sold separately).

Pin No

Pin Function

Pin 3

CAN Bus 3 Low Signal (Available only on 4x CAN Model)

Pin 4

Analog Input 1 - do not apply voltages outside of the -10 to +10V range

Pin 5

Pin 6

CAN Bus 1 Low Signal

Pin 7

CAN Bus 0 Low Signal

Pin 9

+5V to +27V Supply Voltage

Pin 10

+4.5V Instrumentation Supply Voltage, ensure that current draw is not more than 100mA

Pin 11

Erase PIN

Pin 12

Digital Input 0 - When used as an input, do not apply voltages outside the 0 to +12V range.

More information on the use of this pin can be found in Appendix 2

Pin 13

CAN Bus 2 Low Signal (Available only on 4x CAN Model)

Pin 15

LIN 0 Signal

Pin 16

CAN Bus 3 High Signal (Available only on 4x CAN Model)

Pin 17

Analog Input 0 - do not apply voltages outside of the -10 to +10V range

Pin 18

Analog Ground

Pin 19

CAN Bus 1 High Signal

Pin 20

CAN Bus 0 High Signal

Pin 21

Ground

Pin 22

Power Ground

Pin 23

Relay Out (Optional Feature)

Pin 24

Digital Input 1 - When used as input, do not apply voltages outside the 0 to +12V range

PIN 25

CAN Bus 2 High Signal (Available only on 4x CAN Model)

Notes:

The connector needs to be tightened properly to make a proper connection, ensuring reliable operation.
Each end of the CAN bus must be terminated with a 120 Ohm resistor across CAN H & CAN L.
Do not short-circuit any pins.
The maximum safe applied voltage for analogue and digital I/P is ±28 V.

Attention:

To set up a USB via the Molex connector, please specify this requirement when ordering, or the device must be sent back to Influx (as this requires some hardware modification).

The OBD & INST Connector

The OBD & INST Connector is a Male 25-pin Standard D Type Connector with nuts.

Pin No

Pin Function

Pin 1

Analog Input 3- do not apply voltage outside of the -10 to +10 V range

Pin 2

LIN 1

Pin 3

CAN / CAN FD Bus 3 Low signal

Pin 4

Analog Input 1 - do not apply voltages outside of the -10 to +10V range

Pin 5

Wake-Up pin to wake logger from sleep mode (for use, see Appendix 1)

Pin 6

CAN Bus 1 (Medium Speed Bus) Low Signal

Pin 7

CAN Bus 0 (High-Speed Bus) Low Signal

Pin 8

Pin 9

4.5-36V Supply Voltage

Pin 10

+4.5V Instrumentation Supply Voltage, ensure that the current drawn is not more than 100mA

Pin 11

Digital Input or Output 2 - Do not apply voltages outside of the 0 to +12V range when used as an input. When used as an Output, ensure that the current drawn is not more than 100mA.

More information on the use of this pin can be found in Appendix 2 and 3

Pin 12

Digital Input or Output 0 - Do not apply voltages outside the 0 to +12V range when used as an input. When used as an Output, ensure that the current drawn is not more than 100mA.

More information on the use of this pin can be found in Appendix 2 and 3

Pin 13

CAN /CAN FD Bus 2 (Instrumentation Bus) Low Signal

Pin 14

Analog Input 2 - - do not apply voltages outside of the -10 to +10V range

Pin 15

LIN 0

Pin 16

CAN / CAN FD Bus 3 High signal

Pin 17

Analog Input 0 - - do not apply voltages outside of the -10 to +10V range

Pin 18

Analog Ground

Pin 19

CAN Bus 1 (Medium Speed Bus) High Signal

Pin 20

CAN Bus 0 (High-Speed Bus) High Signal

Pin 21

Ground - e.g. to be connected to pin 5 of the OBDII Connector

Pin 22

Power Ground - e.g. to be connected to pin 4 of the OBDII Connector

Pin 23

Digital Input or Output 3 (can also be used as a switched power supply +Vd). Do not apply voltages outside of the 0 to +12V range when used as an input.

Pin 24

Digital Input or Output 1 - Do not apply voltages outside of the 0 to +12V range when used as an input. When used as an Output, ensure that the current drawn is not more than 100mA.

More information on the use of this pin can be found in Appendix 2 and 3

Pin 25

CAN / CAN FD Bus 2 (Instrumentation Bus) High Signal

WARNING

DON'T SHORT CIRCUIT OR OVERLOAD AND DIGITAL I/O, e.g. IF USING DIGITAL INPUT OUTPUT 3 TO SUPPLY POWER TO POWER A K-BOX OR A REBEL DASH, DO NOT CONNECT MORE THAT 1 K-BOX TO THIS OUTPUT AND BE CAREFUL THAT NO SHORT CIRCUIT OCCURS.

WARNING

OVERLOADING (I > 100mA) OF PIN 10 (+4.5V Instrumentation) WILL RESULT IN A DROP IN THE OUTPUT VOLTAGE.

WARNING

EACH END OF THE CAN BUS MUST BE TERMINATED WITH A 120 OHM RESISTOR ACROSS CAN H AND CAN L. THE LOGGER HAS DIP SWITCHES INSIDE THAT MAY BE TURNED ON IF IT IS AT THE END OF A CAN BUS TO ALLOW THE BUS TO BE TERMINATED EASILY.

K-Box

(INF 2201)

The CAN Connectors (2x DB9 CAN Connectors)

The CAN Connectors are 1x Male and 1x Female 9-pin Standard D Type Connectors with nuts.

Pin No

Pin Function

Pin 1

Digital Output 4 or +4.5V Instrumentation Supply Voltage, ensure that current draw is not more than 100mA

Pin 2

CAN Bus Low Signal

Pin 3

Ground

Pin 4

Digital Input or Output 1 - Do not apply voltages outside of the 0 to +12V range when used as an input. When used as an Output, ensure that the current drawn is not more than 100mA. More information on the use of this pin can be found in Appendix 2 and 3

Pin 5

Power Ground

Pin 6

Digital Input or Output 3

Pin 7

CAN Bus High Signal

Pin 8

Digital Input or Output 2 - Do not apply voltages outside of the 0 to +12V range when used as an input. When used as an Output, ensure that the current drawn is not more than 100mA. More information on the use of this pin can be found in Appendix 2 and 3

Pin 9

4.5-36V Supply Voltage

WARNING:

Each End of the CAN bus must be terminated with a 120-ohm resistor across CAN H and CAN L.

The ADC Connector

The ADC Connector is a Male 25-pin Standard D-Type Connector with nuts.

Pin No

Pin Function

Pin 1

+24V Output - ensure that the current drawn is not more than 75mA

Pin 2

+5V Output - ensure that the current drawn is not more than 75mA

Pin 5

Analog Ground

Pin 6

Analog Input 0 + ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 7

Analog Input 1 + ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 8

Analog Input 2 + ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 9

Analog Input 3 + ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 10

Analog Input 4 + ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 11

Analog Input 5 + ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 12

Analog Input 6 + ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 13

Analog Input 7 + ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 14

Ground Out

Pin 15

Ground Out

Pin 17

Analog Ground

Pin 18

Analog Input 0 - ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 19

Analog Input 1 - ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 20

Analog Input 2 - ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 21

Analog Input 3 - ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 22

Analog Input 4 - ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 23

Analog Input 5 - ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 24

Analog Input 6 - ve (do not apply voltages outside the voltage range the K-Box is configured for).

Pin 25

Analog Input 7 - ve (do not apply voltages outside the voltage range the K-Box is configured for).

The Thermocouple Connectors

The Thermocouple Connectors on the K-Box are miniature-size flat-type sockets.

IEC Connector

Pin Function

Top

+ Signal from the Thermocouple

Bottom

K Signal from the Thermocouple

The dimensions of the Male Flat Type Miniature Size Thermocouple Plug that you would plug into it are as follows:

Note:

Pins not mentioned in the description table(s) are NC.

K-AN8

(INF 2210)

The CAN Connectors

(2x DB9 CAN Connectors)

The CAN Connectors are 1x Male and 1x Female 9-pin Standard D Type Connectors with nuts.

Pin No

Pin Function

Pin 1

Digital Output 4 or +4.5V Instrumentation Supply Voltage, ensure that the current drawn is not more than 100mA

Pin 2

CAN Bus Low Signal

Pin 3

Ground

Pin 4

Pin 5

Power Ground

Pin 6

Digital Input or Output 3

Pin 7

CAN Bus High Signal

Pin 8

Pin 9

4.5-36V Supply Voltage

WARNING:

Each end of the CAN bus must be terminated with a 120ohm resistor across CAN H and CAN L.

The ADC Connector

The ADC Connector is a Male 25-pin Standard D-Type Connector with nuts.

Pin No

Pin Function

Pin 1

+24V Output - ensure that the current drawn is not more than 75mA

Pin 2

+5V Output - ensure that the current drawn is not more than 75mA

Pin 5

Analog Ground

Pin 6

Analog Input 0 + ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 7

Analog Input 1 + ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 8

Analog Input 2 + ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 9

Analog Input 3 + ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 10

Analog Input 4 + ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 11

Analog Input 5 + ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 12

Analog Input 6 + ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 13

Analog Input 7 + ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 14

Ground Out

Pin 15

Ground Out

Pin 17

Analog Ground

Pin 18

Analog Input 0 - ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 19

Analog Input 1 - ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 20

Analog Input 2 - ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 21

Analog Input 3 - ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 22

Analog Input 4 - ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 23

Analog Input 5 - ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 24

Analog Input 6 - ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Pin 25

Analog Input 7 - ve (do not apply voltages outside the voltage range the K-AN8 is configured for).

Note:

Pins not mentioned in the description table(s) are NC.

K-IEPE Pinouts (Add-On) (INF 2213) (Add-On)

(INF 2213) (Add-On)

The IEPE BNC Connector

The K IEPE Connector

The K IEPE Connector is a Female 25-pin Standard D Type Connector with nuts.

Pin No

Pin Function

Pin 1

+24V Output - ensure that the current drawn is not more than 75mA

Pin 2

+5V Output - ensure that the current drawn is not more than 75mA

Pin 5

Analog Ground

Pin 6

Analog Input 0 + ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 7

Analog Input 1 + ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 8

Analog Input 2 + ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 9

Analog Input 3 + ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 10

Analog Input 4 + ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 11

Analog Input 5 + ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 12

Analog Input 6 + ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 13

Analog Input 7 + ve(do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 14

Ground Out

Pin 15

Ground Out

Pin 17

Analog Ground

Pin 18

Analog Input 0 - ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 19

Analog Input 1 - ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 20

Analog Input 2 - ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 21

Analog Input 3 - ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 22

Analog Input 4 - ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 23

Analog Input 5 - ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 24

Analog Input 6 - ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Pin 25

Analog Input 7 - ve (do not apply voltages outside the voltage range the K-IEPE is configured for).

Note:

Pins not mentioned in the description table(s) are NC.

Pinout of the Multi Connect Cable

The Standard Display Cable may be connected to the multi-connect cable's AUX cable to connect it to the Rebel CT or LT Loggers. The pinout is as follows:

AUX (The port of the Multi Connect Cable that is typically used with the Rebel Dash)

DB9

Pin Function

Pin 2

CAN 1(MS) L

Pin 3

Ground

Pin 5

Ground

Pin 7

CAN 1(MS) H

Pin 9

Power Supply Switched

CAN+PWR (This Connector is used to power the Logger; e.g. it could be powered via the diagnostics connector of a vehicle connected to the OBD2 to DB9 Cable.)

DB9

Pin Function

Pin 1

CAN 1 (MS) L

Pin 2

CAN 0 (HS) L

Pin 3

Ground

Pin 4

K-Line

Pin 5

Power Ground

Pin 7

CAN 0 (HS) H

Pin 8

CAN 1 (MS) H

Pin 9

Power Supply 4.5-36V (10-32V is required for the Rebel Dash to operate)

Digital/Analog (This Connector connects Digital and Analog signals to the Logger.)

DB15

Pin Function

Pin 2

Digital I/0 1

Pin 3

+4.5V Instrumentation

Pin 4

Ground

Pin 6

Analog Ground

Pin 7

Ain1 inst

Pin 8

Ain3 inst

Pin 9

Digital I/0 0

Pin 10

Digital I/0 2L

Pin 11

Ground

Pin 13

Wake-Up #

Pin 14

Ain0 inst

Pin 15

Ain2 inst

LAN/CAN (Used for connecting CAN2 and Ethernet to the Logger.)

DB9

Pin Function

Pin 1

Lan RX-

Pin 2

CAN 2 (Inst) L

Pin 3

Power Ground

Pin 4

Lan TX+

Pin 5

Ain0 inst

Pin 6

Lan RX+

Pin 7

CAN 2 (Inst) H

Pin 8

Lan TX-

Pin 9

Digital I/O 3 or Power Supply Switched

OBD&INST (The multi-connect cable attaches to the Logger via this connector.)

DB25

Pin Function

Pin 1

Ain3 inst

Pin 2

LAN RX-

Pin 3

LAN TX-

Pin 4

Ain1 inst

Pin 5

Wake-UP#

Pin 6

CAN 1 (MS) L

Pin 7

CAN 0 (HS) L

Pin 8

K-Line

Pin 9

4.5-36V (10-32V is required for the Rebel Dash to operate)

Pin 10

+4.5V instrumentation

Pin 11

Digital I/O 2

Pin 12

Digital I/O 0

Pin 13

CAN 2 (INST) L

Pin 14

Ain2 inst

Pin 15

LAN TX+

Pin 16

LAN RX+

Pin 17

Ain0 inst

Pin 18

Analog Ground

Pin 19

CAN 1 (MS) H

Pin 20

CAN 0 (HS) H

Pin 21

Ground

Pin 22

Power Ground

Pin 23

Digital I/O 3/+Vd

Pin 24

Digital I/O 1

Pin 25

CAN 2 (INST) H

Note:

Pins not mentioned in the description table(s) are NC.

The OBD & INST Connector

The OBD & INST Connector is a Male 25-pin Standard D Type Connector nut.

Pin No

Pin Function

Pin 1

Analog Input 3 - do not apply voltages outside of the -10 to +10V range

Pin 2

Pin 3

Pin 4

Analog Input 1 - do not apply voltages outside of the -10 to +10V range

Pin 5

Wake-Up pin to wake logger from sleep mode (for use, see Appendix 1)

Pin 6

CAN Bus 1 (Medium Speed Bus) Low Signal

Pin 7

CAN Bus 0 (High-Speed Bus) Low Signal

Pin 8

K-Line (1 wire bus) of ISO 9141

Pin 9

4.5-36V Supply Voltage

Pin 10

+4.5V Instrumentation Supply Voltage, ensure that the current drawn is not more than 100mA

Pin 11

Digital Input or Output 2 - Do not apply voltages outside of the 0 to +12V range when used as an input. When used as an Output, ensure that the current drawn is not more than 100mA.

More information on the use of this pin can be found in Appendix 2 and 3

Pin 12

Digital Input or Output 0 - Do not apply voltages outside the 0 to +12V range when used as an input. When used as an Output, ensure that the current draw is not more than 100mA.

More information on the use of this pin can be found in Appendix 2 and 3

Pin 13

Pin 14

Analog Input 2 - do not apply voltages outside of the -10 to +10V range

Pin 15

Pin 16

Pin 17

Analog Input 0 - do not apply voltages outside of the -10 to +10V range

Pin 18

Analog Ground

Pin 19

CAN Bus 1 (Medium Speed Bus) High Signal

Pin 20

CAN Bus 0 (High-Speed Bus) High Signal

Pin 21

Ground

Pin 22

Power Ground

Pin 23

Digital Input or Output 3 (can also be used as a switched power supply +Vd). When used as an input, do not apply voltages outside of the 0 to +12V range

Pin 24

Digital Input or Output 1 - Do not apply voltages outside of the 0 to +12V range when used as an input. When used as an Output, ensure that the current drawn is not more than 100mA.

More information on the use of this pin can be found in Appendix 2 and 3

Pin 25

WARNING

DON'T SHORT CIRCUIT OR OVERLOAD ANY DIGITAL I/O e.g. IF USING DIGITAL INPUT OR OUTPUT 3 TO SUPPLY TO POWER A K-BOX OR REBEL DASH, DO NOT CONNECT MORE THAN ONE K-BOX TO THIS OUTPUT AND BE CAREFUL THAT NO SHORT CIRCUIT OCCURS.

WARNING

OVERLOADING (I > 100mA) ON PIN 10 (+4.5V Instrumentation) WILL RESULT IN A DROP IN THE OUTPUT VOLTAGE.

WARNING

EACH END OF THE CAN BUS MUST BE TERMINATED WITH A 120 OHM RESISTOR ACROSS CAN H AND CAN L. THE LOGGER HAS DIP SWITCHES INSIDE, WHICH MAY BE TURNED OFF IF IT IS AT THE END OF A CAN BUS TO ALLOW THE BUS TO BE TERMINATED.