1 of 93

Cables & Device Pinouts: Influx Product Range

Cables

INF4100: Rebel Start-Up Kit Harness

This cable is specifically designed to work with the Rebel 100, making it easier access the data loggerIO during the early engineering development stages.

The Rebel 100 is designed to be installed for long term event monitoring on production machinery and therefore the connector type is the same that you would normally find on an ECU. This type of connector is not very convenient for engineering development since these connectors are harder to work with. The Rebel100 start-up harness will enable you to connect to the Rebel 100 using standard9 PIN D-Sub connectors like the Rebel CT multi-connect cable.

Tech Specs:

Data Logger Socket.

CAN0/CAN1/Kline/PWR Connector

Male 9-pin standard D-type connector with screws

Note:

Pins not mentioned in the description table(s) are NC.

CAN 1 Connector

Female 9-pin standard D-Type connector with screws

Note:

Pins not mentioned in the description table(s) are NC.

CAN 2 Connector

Male 9-pin standard D-type connector with nuts

Note:

Pins not mentioned in the description table(s) are NC.

CAN 3 Connector

Male 9-pin standard D-type connector with nuts

Note:

Pins not mentioned in the description table(s) are NC.

Digital and Analog Connector

Male 15-pin standard D-type connector with screws

Note:

Pins not mentioned in the description table(s) are NC.

OBDII Connector

Male 16-pin OBDII connector

Note:

Pins not mentioned in the description table(s) are NC.

INF4103: 180-degree OBD Type-B to 9-Way Sub D Adapter Cable

This 1.7-meter cable with 180-degree Type B connector to (female screw) enables you to connect devices (CiA 303-1 compliant) to the vehicle OBD port.

How to use with the Rebel data loggers

To use this cable with a Rebel data logger you will also need one of our Rebel multi-connect breakout cables. This cable combination enables CAN 0 of the Rebel data logger to be directly connected to the vehicle diagnostic CAN bus and also the permanent battery supply.

Use with either:

INF4203: 2 CAN breakout cable (4 Lead)
INF4204.1: Multi-Connect Cable for Rebel data loggers (5 Lead)

How to use with the ReXgen data loggers

This cable enables a direct connection from the ReXgen 9 Way D-Sub to the vehicle diagnostic

CAN bus and also the permanent battery supply.

How to use with Kvaser Interfaces

This cable enables a direct connection from the Kvaser 9-Way D-Sub to the vehicle diagnostic CAN bus and battery supply.

Note that Type B can connect to type A port.

Tech Specs:

OBDII Connector

Male 16-pin OBDII connector

Note:

Pins not mentioned in the description table(s) are NC.

INF 42XX.XX

: Rebel FlexRay/CAN Breakout Cable

: Rebel LT CAN Bus Breakout Cable

: Rebel Multi-Connect Cable (5 Lead)

: 180-degree OBD Type-B Cable to Rebel Data Logger Adapter cable

: Rebel Dash Cable

: 25-way to 25-way D-sub shielded cable

: 9-way D-Sub screw terminal Male

: 9 way D-Sub screw terminal Female

: Multi-Connect digital and analog I/O terminal

: 25-way D-sub screw terminal Female

ReXgen Air cable automotive connector to 25 way D-sub

INF4202: Rebel FlexRay/CAN Breakout Cable

Connects to the expansion port of the Rebel CT FlexRay and Rebel CT 7 data logger. The LIN bus, CAN buses and FleXray channels are connected to separate 9-Way D-Sub moulded connectors. This cable consists of two FlexRay connectors, three CAN buses connectors and one LIN connector.