Start-up Guide: ReXgen Pro

After reflashing, the logger will automatically reconnect to the software to download the ReXdesk software

1. Visit Influx Technology.com >> Support >> ReXgen Series >> Software links >> ReXdesk Download

2. Windows Search >> ReXgen Drivers >> Select and Install

WARNING:

CAN Bus is not isolated.

Notes:

• CAN Bus Isolators can be purchased separately.

SIM CARD INSERTION (for devices with non-soldered SIM cards)

Also, ensure the SIM is inserted, as shown in the images above (Chip facing upwards).

LED Indicators: The 8 LEDs on the ReXgen Pro indicate—

LED	Function	Indication
LED 1	CAN 0	Bold: CAN0 config active Slow Blinking: Logging CAN0 Data Fast Blinking: Baud Rate mismatch/CAN Error/Check connection
LED 2	CAN 1	Bold: CAN1 config active Slow Blinking: Logging CAN1 Data Fast Blinking: Baud Rate mismatch/CAN Error/Check connection
LED 3	CAN 2	Bold: CAN2 config active Slow Blinking: Logging CAN2 Data Fast Blinking: Baud Rate mismatch/CAN Error/Check connection
LED 4	CAN 3	Bold: CAN3 config active Slow Blinking: Logging CAN3 Data Fast Blinking: Baud Rate mismatch/CAN Error/Check connection
LED 5	AIP	Bold: Application Interface Platform is active (any other pattern indicates possible faults)
LED 6	GNSS	Bold: GNSS Configured OFF: Not Configured Blinking: Valid Fix
LED 7	LTE	Bold: Connected to LTE OFF: No LTE connected Blinking: Data is transferred over the LTE interface
LED 8	Wi-Fi	Bold: Connected to Wi-Fi OFF: No interface connected Blinking: Data is transferred over the Wi-Fi interface

ReXgen Pro Connector Details (JAE Compact Automotive 34-pin Connector)

Pin	Function	Description
Pin 2	GND	Ground
Pin 3	Lin0	LIN 0
Pin 11	Can0-L	CAN0-Low Signal
Pin 12	Can1-L	CAN1-Low Signal
Pin 13	Can2-L	CAN2-Low Signal
Pin 14	Can3-L	CAN3-Low Signal
Pin 18	6.5-27V	6.5-27V Supply Voltage
Pin 19	PowerGND	Power Ground
Pin 28	Can0-H	CAN0-High Signal
Pin 29	Can1-H	CAN1-High Signal
Pin 30	Can1-H	CAN2-High Signal
Pin 31	Can3-H	CAN3-High Signal

The JAE Compact automotive 34-pin Connector to D-sub 25 connector can be purchased separately. (Sold separately).

Pin	Function	Description
Pin 2	LIN2	LIN 2 Signal
Pin 3	Can3-L	CAN Bus 3 Low Signal
Pin 6	Can1-L	CAN Bus 1 Low Signal
Pin 7	Can0-L	CAN Bus 0 Low Signal
Pin 8	LIN1	NC
Pin 9	6.5-27V	6.5-27V Supply Voltage
Pin 13	Can2-L	CAN Bus 2 Low Signal
Pin 15	LIN1	LIN 1 Signal
Pin 16	Can3-H	CAN Bus 3 High Signal
Pin 18	GndA	Analog Ground
Pin 19	Can1-H	CAN Bus 1 High Signal
Pin 20	Can0-H	CAN Bus 0 High Signal
Pin 21	GND	Ground
Pin 22	PowerGND	Power Ground
Pin 23	+Vd	Positive Drain Voltage
Pin 25	Can2-H	CAN Bus 2 High Signal

RJ45 (Ethernet connector)

Pin	Function	Description
Pin 1	TrD1_P	TX+_D1 (White with orange stripe)
Pin 2	TrD1_N	TX-_D1 (Orange with white stripe or solid orange)
Pin 3	TrD2_P	RX+_D2 (White with green stripe)
Pin 6	TrD2_N	RX-_D2 (Green with white stripe or solid)

Notes:

• REFER TO THE PRODUCT MANUAL FOR DETAILED PINOUT.

How to configure Wi-Fi settings to start up REXGEN Pro.

Note:

• The default password is 12345678.

Open the Wi-Fi settings on your device (laptop, mobile, or tablet). Select the default serial number of your Pro device. Select the Wi-Fi that you wish to connect to on the Wi-Fi configuration window, and click 'Configure'.

Note:

• The default password is 12345678.

Upon clicking Configure, the 'Wi-Fi hotspot' will get disconnected.

The status of LED 8 indicates the Wi-Fi configuration status. Once the hotspot connection is successful, LED 8 will turn bold after a one-minute pause.

Once the configuration is successful and the device is connected to the specified Wi-Fi.

Note:

• Ensure your system and the ReXgen Pro device are connected to the same Wi-Fi.

• Once configured, open the ReXdesk software and click the USB icon on the status bar (located in the lower-left corner).

• Click on TCP/IP and scan for local networks.

• Scan Local Network.

• Select the name and IP of your Pro device, and click Connect.

Click OK to exit the ReXgen Connect window.

Once completed, the status on the status bar is updated to 'CONNECTED'.

To update the firmware

Open ReXdesk, connect the logger and click the ‘Reflash’ option under the Device tab.

Reflash – Select the required firmware to update the logger.

Notes:

• Do not disconnect the logger until the logger LED stops flashing. After reflashing, the logger will automatically reconnect to the software.

• Please ensure that the internal storage is formatted after reflashing the logger.

To set the time

• Open ReXdesk, connect the logger and click ‘Set Time’ on the top taskbar.

• To synchronise the logger’s time with your PC, select ‘Synchronise with PC.

Or

• To manually set the logger’s time, select ‘Set Custom Date Time’.

• Click ‘Set Time” to save.

To start logging

• Open ReXdesk, connect the logger, double-click, or drag and drop the ‘Log All’ icon into the configuration window.

• Click the ‘Run’ icon on the top taskbar and save the project.

• Once the Configuration is uploaded successfully, click OK.

To open a data log from internal storage

• Click the ‘Internal Storage’ icon on the top taskbar and select the file you wish to open.

• Click on the ‘Download’ tab and select the required format for download.

Notes:

• Always ensure the device is installed, connected, and commissioned by a qualified professional.

• The device must only be repaired by the manufacturer.

How to enable Cloud settings for the ReXgen Pro logger

• Click the Tool tab in the Navigation bar and select Cloud Settings.

• Select the Mobile option and then select the ‘New Mobile’ option.

• Select the ‘S3 ‘option and the ‘New S3’ option.

How to enable AWS configuration in the ReXgen logger

• Prepare the base configuration for the logger.

• In the Device Configuration window, click on the 'Upload' tab.

• Enable the 'checkbox' for 'Enable AWS'.

  • For a single setting, details are auto-filled in the subsequent sections.

  • Users can select the desired setting from the corresponding drop-down menus for multiple settings.

• Click the ‘Run’ tab in the Navigation bar.

• Save the project:

  • Save Project: allows you to save the Project with a user-defined name.

  • Continue as "New Project”: saves the" New Project" configuration.

• Click ‘OK’ once the configuration is uploaded successfully.

How do you upload the configuration to the logger via AWS?

• Make the new configuration.

• Enable AWS from the Device Configuration menu.

Notes:

• Set your configuration check time in the given section.

• Save the Project with the name you require for the configuration.

• Under the ‘Config’ tab, select Export from the drop-down menu.

• Select ‘Export ReXgen Configuration (rxc)’ from the listed options.

• Save the file with the desired name.

• Click ‘Save''.

• Once saved, rename the file as 'config.rxc.'

Notes:

• Ensure that you rename the file as 'config.rxc' only.

How to configure Wi-Fi settings to start up a Pro device.