Pinouts: Rebel CT Logger
the following contains the details of the pinouts for Rebel CT Logger (RC-5-2) (INF 210 5/6/7/8)
The USB Connector
The USB Connector is a USB Series “B” Receptacle Interface.
Pin No | Pin Function |
Pin 1 | VBUS USB supply voltage 5V |
Pin 2 | Data- line of USB, this signal utilises NRZI line coding |
Pin 3 | Data+ line of USB, this signal utilises NRZI line coding |
Pin 4 | Ground |
The OBD & INST Connector
The OBD & INST Connector is a Male 25-pin Standard D Type Connector with nuts.
Pin No | Pin Function |
Pin 1 | Analog Input 3- do not apply voltage outside of the -10 to +10 V range |
Pin 2 | LIN 1 |
Pin 3 | CAN/CAN FD Bus 3 Low signal |
Pin 4 | Analog Input 1 - do not apply voltages outside of the -10 to +10V range |
Pin 5 | Wake-Up pin to wake logger from sleep mode (for use, see Appendix 1) |
Pin 6 | CAN Bus 1 (Medium Speed Bus) Low Signal |
Pin 7 | CAN Bus 0 (High-Speed Bus) Low Signal |
Pin 9 | 4.5-36V Supply Voltage |
Pin 10 | +4.5V Instrumentation Supply Voltage, ensure that the current drawn is not more than 100mA |
Pin 11 | Digital Input or Output 2 - Do not apply voltages outside of the 0 to +12V range when used as an input. When used as an Output, ensure that the current drawn is not more than 100mA. More information on the use of this pin can be found in Appendix 2 and 3 |
Pin 12 | Digital Input or Output 0 - Do not apply voltages outside the 0 to +12V range when used as an input. When used as an Output, ensure that the current drawn is not more than 100mA. More information on the use of this pin can be found in Appendix 2 and 3 |
Pin 13 | CAN/CAN FD Bus 2 (Instrumentation Bus) Low Signal |
Pin 14 | Analog Input 2 - - do not apply voltages outside of the -10 to +10V range |
Pin 15 | LIN 0 |
Pin 16 | CAN/CAN FD Bus 3 High signal |
Pin 17 | Analog Input 0 - - do not apply voltages outside of the -10 to +10V range |
Pin 18 | Analog Ground |
Pin 19 | CAN Bus 1 (Medium Speed Bus) High Signal |
Pin 20 | CAN Bus 0 (High-Speed Bus) High Signal |
Pin 21 | Ground - e.g. to be connected to pin 5 of the OBDII Connector |
Pin 22 | Power Ground - e.g. to be connected to pin 4 of the OBDII Connector |
Pin 23 | Digital Input or Output 3 (can also be used as a switched power supply +Vd). Do not apply voltages outside of the 0 to +12V range when used as an input. |
Pin 24 | Digital Input or Output 1 - Do not apply voltages outside of the 0 to +12V range when used as an input. When used as an Output, ensure that the current drawn is not more than 100mA. More information on the use of this pin can be found in Appendix 2 and 3 |
Pin 25 | CAN/CAN FD Bus 2 (Instrumentation Bus) High Signal |
WARNING:
Don't short circuit or overload any Digital I/O, e.g. If using Digital Input or Output 3 to the power supply to power a K-Box or Rebel Dash, do not connect more than 1 K-Box to this output and be careful that no short circuit occurs.
Overloading (I > 100mA) of Pin 10 (+4.5V Instrumentation) will result in a drop in the output voltage.
Each End of the CAN bus must be terminated with a 120 Ohm resistor across CAN H and CAN L, and The Logger has dip switches inside that may be turned on if it is at the end of a CAN bus to allow the bus to be terminated easily.
The GPS Connector
The Optional GPS Connector is a Male SMB Connector.
Pin No | Pin Function |
Pin 1 | Radio Frequency Signal Input |
Pin 2 | Ground |
The GPRS Connector
The Optional GPRS Connector is a Male RP-SMA Connector.
Pin No | Pin Function |
Pin 1 | Radio Frequency Signal Input |
Pin 2 | Ground |
The WiFi Connector
The Optional WiFi Connector is a Female RP-SMA Connector.
Pin No | Pin Function |
Pin 1 | Radio Frequency Signal Input |
Pin 2 | Ground |
The GPS Connector
The Optional GPS Connector is a Male SMB Connector.
Pin No | Pin Function |
Pin 1 | Radio Frequency Signal Input |
Pin 2 | Ground |
The FlexRay/LIN & Can Ext Connector
The Optional FlexRay Connector is a Male 15-pin 1.27mm Pitch Micro D Connector nut.
Pin No | Pin Function |
Pin 1 | CAN Bus 4 (Ext 1) Low Signal |
Pin 2 | CAN Bus 4 (Ext 1) High Signal |
Pin 3 | CAN Bus 5 (Ext 2) Low Signal |
Pin 4 | CAN Bus 5 (Ext 2) High Signal |
Pin 5 | CAN Bus 6 (Ext 3) Low Signal |
Pin 6 | CAN Bus 6 (Ext 3) High Signal |
Pin 7 | LIN (Local Interconnect Network) Bus |
Pin 8 | +Vin Supply Voltage |
Pin 9 | FlexRay Bus 1 BP Signal |
Pin 10 | FlexRay Bus 1 BM Signal |
Pin 11 | FlexRay Bus 2 BP Signal |
Pin 12 | FlexRay Bus 2 BM Signal |
Pin 13 | Ground for the FlexRay Buses |
Pin 14 | Ground for the CAN and LIN Buses |
Pin 15 | Power Ground |
Last updated
