Start-up Guide: ReXgen Air

To download the ReXdesk software

1. Visit Influx Technology.com >> Support >> ReXgen Series >> Software links >> ReXdesk Download

2. Windows Search >> ReXgen Drivers >> Select and Install

WARNING:

• CAN Bus and USB are not isolated.

• CAN Bus and USB Isolators can be purchased separately.

• Care must be taken when plugging the USB into the device.

• Removing the power supply when the device is connected to a PC via USB is recommended.

• Signal inputs (CAN, analogue or digital) should not exceed ±28 V.

• For stable operation, ensure all sensors and inputs share the same ground as the unit's power supply.

• Please do not use the logger's USB port for stand-alone data logging, as it may damage the port and will not be covered under warranty.

• ReXgen Air is an IP50 device (please ensure it is covered when mounting it in locations that may have water ingress).

SIM Card Insertion

To insert the SIM card into a ReXgen Air device, open the SIM slot lid correctly and carefully.

Locate the SIM slot: Open the SIM cover and identify the SIM slot.

Check orientation: Hold the SIM card with gold contacts facing down and the cut corner aligned with the slot.

Insert only into the SIM slot: Slide the SIM card straight into the slot until it stops. Warning: Do not place the SIM anywhere else: it may fall inside the logger.

Close the cover: Once fully inserted, reattach the SIM cover.

Ensure the SIM is inserted, as shown, in the images above (chip facing down).

Mishandling the SIM slot lid may damage the device and the SIM card inside.

24-pin Molex Mini50 Connector Details

PIN Number	PIN Function	Optional
PIN 1	RelayOut0	Relay Driver
PIN 2	DigIn0
PIN 3	AnalogGnd
PIN 4	Adc1
PIN 5	Wake-UP/Clamp-15
PIN 6	CAN0-L
PIN 7	CAN1-L
PIN 8	CAN2-L	Additional CAN FD 3rd bus
PIN 9	CAN3-L	Additional CAN FD 4th bus
PIN 10	usbDP_conn	Request when ordering
PIN 11	4.5Vout
PIN 12	DIgIn1
PIN 13	Adc0
PIN 14	Erase#
PIN 15	LIN
PIN 16	GND
PIN 17	PowerGND
PIN 18	5V to 27V
PIN 19	CAN0-H
PIN 20	CAN1-H
PIN 21	CAN2-H	Additional CAN FD 3rd bus
PIN 22	CAN3-H	Additional CAN FD 4th bus
PIN 23	usb5V	Request when ordering
PIN 24	usbDM_conn	Request when ordering

Pinout Details for all ReXgen Air connectors.

INF4204.1: Rebel Multi-Connect Cable (5 Lead)

INF4204.15: MOLEX – 5WAY DB9 SPLITTER CONNECTOR

Warning:

• The connector must be tightened securely to ensure correct connection and reliable operation.

• Each end of the CAN bus must be terminated with a 120 Ohm resistor across CAN H & CAN L.

• Do not short-circuit any pins.

• Signal inputs (CAN, analogue or digital) should not exceed ±28 V.

• For stable operation, ensure all sensors and inputs share the same ground as the unit's power supply

• Please do not use the logger's USB port for stand-alone data logging, as it may damage the port and will not be covered under warranty.

• ReXgen Air is an IP50 device (please ensure it is covered when mounting it in locations that may have water ingress).

To update the firmware

Open ReXdesk, connect the logger and click the ‘Reflash’ option under the Device tab.

Reflash – Select the required firmware to update the logger.

Warning:

• Do not disconnect the logger until the logger LED stops flashing. The logger will automatically reconnect to the software after reflashing.

• Please ensure that the internal storage is formatted after reflashing the logger.

LED Indicators

The 4 LEDs on the ReXgen Air indicate CAN/CAN FD logging activity.

LED	Indication when BOLD	Indication when BLINKING
LED 1	Configured for CAN 0 Log	Active logging on CAN 0
LED 2	Configured for CAN 1 Log	Active logging on CAN 1
LED 3	Configured for GPS Log	Active logging
LED 4	NA	Fast Blinking: Attempting to connect. Slow Blinking: Connected

To set the time

Open ReXdesk, connect the logger and click ‘Set Time’ on the top taskbar.

To synchronise the logger’s time with your PC, select ‘Synchronise with PC.

Or

To manually set the logger’s time, select ‘Set Custom Date Time’.

Click ‘Set Time” to save.

To start logging

Open ReXdesk, connect the logger, double-click, or drag and drop the ‘Log All’ icon into the configuration window.

Click the ‘Run’ icon on the top taskbar and save the project.

Once the Configuration is uploaded successfully, click OK.

Set up a REXGEN

Update Firmware

Configure FTP settings

Configure AWS settings

To open a data log from internal storage

Click the ‘Internal Storage’ icon on the top taskbar and select the file you wish to open.

Click on the ‘Download’ tab and select the required format for download.

Notes:

• Always ensure the device is installed, connected, and commissioned by a qualified professional.

• The device must only be repaired by the manufacturer.

• ReXgen Air is an IP50 device (please ensure it is covered when mounting it in locations that may have water ingress).

Refer to ReXgen Air's Product Manual for more details.