Start-up Guide: ReXgen Pro

After reflashing, the logger will automatically reconnect to the software to download the ReXdesk software

  1. Visit Influx Technology.com >> Support >> ReXgen Series >> Software links >> ReXdesk Download

  2. Windows Search >> ReXgen Drivers >> Select and Install

WARNING:

Notes:

  • CAN Bus Isolators can be purchased separately.

SIM CARD INSERTION (for devices with non-soldered SIM cards)

Also, ensure the SIM is inserted, as shown in the images above (Chip facing upwards).

LED Indicators: The 8 LEDs on the ReXgen Pro indicate—

LED

Function

Indication

LED 1

CAN 0

Bold: CAN0 config active

Slow Blinking: Logging CAN0 Data

Fast Blinking: Baud Rate mismatch/CAN Error/Check connection

LED 2

CAN 1

Bold: CAN1 config active

Slow Blinking: Logging CAN1 Data

Fast Blinking: Baud Rate mismatch/CAN Error/Check connection

LED 3

CAN 2

Bold: CAN2 config active

Slow Blinking: Logging CAN2 Data

Fast Blinking: Baud Rate mismatch/CAN Error/Check connection

LED 4

CAN 3

Bold: CAN3 config active

Slow Blinking: Logging CAN3 Data

Fast Blinking: Baud Rate mismatch/CAN Error/Check connection

LED 5

AIP

Bold: Application Interface Platform is active

(any other pattern indicates possible faults)

LED 6

GNSS

Bold: GNSS Configured

OFF: Not Configured

Blinking: Valid Fix

LED 7

LTE

Bold: Connected to LTE

OFF: No LTE connected

Blinking: Data is transferred over the LTE interface

LED 8

Wi-Fi

Bold: Connected to Wi-Fi

OFF: No interface connected

Blinking: Data is transferred over the Wi-Fi interface

ReXgen Pro Connector Details (JAE Compact Automotive 34-pin Connector)

Pin

Function

Description

Pin 2

GND

Ground

Pin 3

Lin0

LIN 0

Pin 11

Can0-L

CAN0-Low Signal

Pin 12

Can1-L

CAN1-Low Signal

Pin 13

Can2-L

CAN2-Low Signal

Pin 14

Can3-L

CAN3-Low Signal

Pin 18

6.5-27V

6.5-27V Supply Voltage

Pin 19

PowerGND

Power Ground

Pin 28

Can0-H

CAN0-High Signal

Pin 29

Can1-H

CAN1-High Signal

Pin 30

Can1-H

CAN2-High Signal

Pin 31

Can3-H

CAN3-High Signal

The JAE Compact automotive 34-pin Connector to D-sub 25 connector can be purchased separately. (Sold separately).

Pin

Function

Description

Pin 2

LIN2

LIN 2 Signal

Pin 3

Can3-L

CAN Bus 3 Low Signal

Pin 6

Can1-L

CAN Bus 1 Low Signal

Pin 7

Can0-L

CAN Bus 0 Low Signal

Pin 8

LIN1

NC

Pin 9

6.5-27V

6.5-27V Supply Voltage

Pin 13

Can2-L

CAN Bus 2 Low Signal

Pin 15

LIN1

LIN 1 Signal

Pin 16

Can3-H

CAN Bus 3 High Signal

Pin 18

GndA

Analog Ground

Pin 19

Can1-H

CAN Bus 1 High Signal

Pin 20

Can0-H

CAN Bus 0 High Signal

Pin 21

GND

Ground

Pin 22

PowerGND

Power Ground

Pin 23

+Vd

Positive Drain Voltage

Pin 25

Can2-H

CAN Bus 2 High Signal

RJ45 (Ethernet connector)

Pin

Function

Description

Pin 1

TrD1_P

TX+_D1 (White with orange stripe)

Pin 2

TrD1_N

TX-_D1 (Orange with white stripe or solid orange)

Pin 3

TrD2_P

RX+_D2 (White with green stripe)

Pin 6

TrD2_N

RX-_D2 (Green with white stripe or solid)

Notes:

  • REFER TO THE PRODUCT MANUAL FOR DETAILED PINOUT.

How to configure Wi-Fi settings to start up REXGEN Pro.

Note:

  • The default password is 12345678.

Open the Wi-Fi settings on your device (laptop, mobile, or tablet). Select the default serial number of your Pro device. Select the Wi-Fi that you wish to connect to on the Wi-Fi configuration window, and click 'Configure'.

Note:

  • The default password is 12345678.

Upon clicking Configure, the 'Wi-Fi hotspot' will get disconnected.

The status of LED 8 indicates the Wi-Fi configuration status. Once the hotspot connection is successful, LED 8 will turn bold after a one-minute pause.

Once the configuration is successful and the device is connected to the specified Wi-Fi.

Note:

  • Ensure your system and the ReXgen Pro device are connected to the same Wi-Fi.

  • Once configured, open the ReXdesk software and click the USB icon on the status bar (located in the lower-left corner).

  • Click on TCP/IP and scan for local networks.

  • Select the IP of your Pro device, and click Connect.

Once completed, the status on the status bar is updated to 'CONNECTED'.

To update the firmware

Open ReXdesk, connect the logger and click the ‘Reflash’ option under the Device tab.

Reflash – Select the required firmware to update the logger.

Notes:

  • Do not disconnect the logger until the logger LED stops flashing. After reflashing, the logger will automatically reconnect to the software.

  • Please ensure that the internal storage is formatted after reflashing the logger.

To set the time

  • Open ReXdesk, connect the logger and click ‘Set Time’ on the top taskbar.

  • To synchronise the logger’s time with your PC, select ‘Synchronise with PC.

Or

  • To manually set the logger’s time, select ‘Set Custom Date Time’.

  • Click ‘Set Time” to save.

To start logging

  • Open ReXdesk, connect the logger, double-click, or drag and drop the ‘Log All’ icon into the configuration window.

  • Click the ‘Run’ icon on the top taskbar and save the project.

  • Once the Configuration is uploaded successfully, click OK.

To open a data log from internal storage

  • Click the ‘Internal Storage’ icon on the top taskbar and select the file you wish to open.

  • Click on the ‘Download’ tab and select the required format for download.

Notes:

  • Always ensure the device is installed, connected, and commissioned by a qualified professional.

  • The device must only be repaired by the manufacturer.

How to enable Cloud settings for the ReXgen Pro logger

  • Click the Tool tab in the Navigation bar and select Cloud Settings.

  • Select the Mobile option and then select the ‘New Mobile’ option.

  • Select the ‘S3 ‘option and the ‘New S3’ option.

How to enable AWS configuration in the ReXgen logger

  • Prepare the base configuration for the logger.

  • In the Device Configuration window, click on the 'Upload' tab.

  • Enable the 'checkbox' for 'Enable AWS'.

    • For a single setting, details are auto-filled in the subsequent sections.

    • Users can select the desired setting from the corresponding drop-down menus for multiple settings.

  • Click the ‘Run’ tab in the Navigation bar.

  • Save the project:

    • Save Project: allows you to save the Project with a user-defined name.

    • Continue as "New Project”: saves the" New Project" configuration.

  • Click ‘OK’ once the configuration is uploaded successfully.

How do you upload the configuration to the logger via AWS?

  • Make the new configuration.

  • Enable AWS from the Device Configuration menu.

Notes:

  • Set your configuration check time in the given section.

  • Save the Project with the name you require for the configuration.

  • Under the ‘Config’ tab, select Export from the drop-down menu.

  • Select ‘Export ReXgen Configuration (rxc)’ from the listed options.

  • Save the file with the desired name.

  • Click ‘Save''.

  • Once saved, rename the file as 'config.rxc.'

Notes:

  • Ensure that you rename the file as 'config.rxc' only.

Last updated